Proven high quality products
for various asphalt applications
ABOUT COMPANY
15 years in the market for the production of chemical products for road construction
We are engaged in development, production, introduction of innovative chemical products
Our production capacity is more than 20,000 tons per year
We provide technical support for our products at all stages
Complete enterprise operation circle
Well-equipped research and technical support laboratories and a research and development centre
3 automated production lines for organic synthesis, vehicle pool, 2 railroad docks, competent personnel, instrumentation and software department
Company's products are certifies, the enterprise acts in accordance with ISO 9001
Our company can perform delivery under DDP, FCA
PRODUCTS
EFRIL
ADHESION
PROMOTER
EFRIL ADHESION PROMOTER 187B
Adhesion between bitumen and aggregate is one of the most important criteria for a highly durable and water damage resistant asphalt pavement
High perfomance characteristics of adhesion between bitumen (grades 50/70, 70/100, and PMB 45/80-55) and various mineral materials (granite, dolomite, crushed gravel, and quartz diorite)
Low concentration of Efril adhesion agent is required
Satisfy the requirements of standard EN 12697-11, the agent was tested and performed perfectly during the following tests: Rolling-Bottle-Test, static water storage, detachment in boiling water
Envirenmentally friendly products
EFRIL
BITUMEN
EMULSIFIER
CATIONIC BITUMEN EMULSIFIER
EFRIL EM 54 (CRS, CMS)
CATIONIC BITUMEN EMULSIFIER
EFRIL EM 86 (CSS)
CATIONIC BITUMEN EMULSIFIER
EFRIL EM 7110
Bitumen emulsions are complicated and good chemistry is required to reach desired emulsion properties. Emulsifying agents Efril are good chemistry is used to rich it
Satisfy the requirements of 3 types of bitumen emulsions (medium, slow rapid settings)
Satisfy the requirements of standard EN 13808
We produce two types of bitumen emulsifiers: cationic and anionic
Low concentration of Efril bitumen mulsifier is required
Environmentally friendly products
Good aggregate covering
EFRIL ADHESION
PROMOTER 187B
Efril 187B is a liquid adhesion promoter
for bitominous binders based on
synergic mix of surfactants
The agent provides high perfomance characteristics of adhesion between bitumen (grades 50/70, 70/100, and PMB 45/80-55) and various mineral materials (granite, dolomite, crushed gravel, and quartz diorite)
Low amount of Efril adhesion promoter, from 0,15 % is needed
Satisfy the requirements of standard EN 12697-11, the agent was tested and performed perfectly during the following tests: Rolling-Bottle-Test, static water storage, detachment in boiling water
Environmentally friendly products
Can be used as a warm-mix additive, from 0,5 % is needed
Efril 187B is available in bulk shipment, or tight head
Steel/plastic drums, or in one-way totes (IBCs) of 1800 lbs net weight
PHYSICAL PROPERTIES
Appearance at 20 °C
yellow to brown viscous liquid
Pour point, °C
- 10
Flash point, °C
80
Viscosity, mPa•s (cP) at 20 °C
950
Density, g/cc at 20 °C
0, 950
Amine value, mg KOH/g
150 - 200
Acid value, mg KOH/g
2
Active ingridients, %wt
87 ± 5
Efril 187B should be stored in normal ambient conditions, in closed container. Under proper storage conditions, it has a storage life of at least two years from the date of manufacturing
Adhesion between bitumen and aggregate is one of the most important criteria for a highly durable and water damage resistant asphalt pavement
CATIONIC BITUMEN EMULSIFIER
EFRIL EM 54 (CRS, CMS)
Liquid emulsifier for cationic rapid and medium setting bitumen emulsions suitable for TACK COAT, PRIME COAT, Pre-coated Chips, Chip-Seal, Fog coat,Dense graded, Open Graded, Rap, Surface dressing
Satisfy the requirements of 2 types of bitumen emulsions (medium, rapid setting)
Low amount of Efril emulsifier, % is needed
Satisfy the requirements of standard EN 13808, ASTM D977-12
Gives good adhesion
Environmentally friendly products
It is suitable for both in-line and batch emulsion plants under these conditions
Emulsions prepared using cationic emulsifier Efril have significantly higher viscosities, which allow specifications to be met at the minimum bitumen content
Efril EM is available in bulk shipment, or in tight head
Steel/plastic drums, or in one-way totes (IBCs) of 1800 lbs net weight
PHYSICAL PROPERTIES AND TYPICAL DATA DEPENDS ON DEFINITE MODIFICATIONS OF EMULSIFIER
Appearance at 20 °C
yellow to brown viscous liquid
Pour point, °C
5
Flash point, °C
75
Viscosity, mPa•s (cP) at 20 °C
250
Density, g/cc at 20 °C
1, 025
CATIONIC BITUMEN EMULSIFIER
EFRIL EM 86 (CSS)
Liquid emulsifier for cationic rapid and medium setting bitumen emulsions suitable for Fog Seal, Tack coat, Prime coat, Slurry Seal, Cape Seal, Microsurfacing, Rap, Pre-coated Chips
Satisfy the requirements of bitumen emulsions (slow setting)
Low amount of Efril emulsifier, % is needed
Satisfy the requirements of standard EN 13808, ASTM D977-12
Gives good adhesion
Environmentally friendly products
It is suitable for both in-line and batch emulsion plants under these conditions
Emulsions prepared using cationic emulsifier Efril have significantly higher viscosities, which allow specifications to be met at the minimum bitumen content
Efril EM is available in bulk shipment, or in tight head
Steel/plastic drums, or in one-way totes (IBCs) of 1800 lbs net weight
PHYSICAL PROPERTIES AND TYPICAL DATA DEPENDS ON DEFINITE MODIFICATIONS OF EMULSIFIER
Appearance at 20 °C
yellow to brown viscous liquid
Pour point, °C
6
Flash point, °C
75
Viscosity, mPa•s (cP) at 20 °C
260
Density, g/cc at 20 °C
1, 030
CATIONIC BITUMEN EMULSIFIER
EFRIL EM 7110
Liquid emulsifier for cationic rapid and medium setting bitumen emulsions suitable for Surface dressing, Fog Seal, Tack coat, Open graded, Rap, Stockpile mix
Satisfy the requirements of bitumen emulsions (rapid, medium,slow setting)
Low amount of Efril emulsifier, % is needed
Satisfy the requirements of standard EN 13808, ASTM D977-12
Gives good adhesion
Environmentally friendly products
It is suitable for both in-line and batch emulsion plants under these conditions
Emulsions prepared using cationic emulsifier Efril have significantly higher viscosities, which allow specifications to be met at the minimum bitumen content
Efril EM is available in bulk shipment, or in tight head
Steel/plastic drums, or in one-way totes (IBCs) of 1800 lbs net weight
PHYSICAL PROPERTIES AND TYPICAL DATA DEPENDS ON DEFINITE MODIFICATIONS OF EMULSIFIER
Appearance at 20 °C
yellow to brown viscous liquid
Pour point, °C
0
Flash point, °C
75
Viscosity, mPa•s (cP) at 20 °C
330
Density, g/cc at 20 °C
1, 060
CONTACT US
Using our products, we guarantee you high
efficiency while saving the budget for the
construction and repair of roads
* obligatory fields